球探即时比分下载

Welcome to the website of Jingjiang Haichen Transmission Parts Factory; it mainly produces coupling series and transmission shaft products.

National Service Hotline
13775696728

company address
Team 10, Zengguang Village, Dongxing Town, Jingjiang City

company news

  • 10

    2020-01

    Drive shaft constant velocity universal joint life test bench

    The equipment host includes test platform, main drive system, driven adjustment system, hydraulic loading system and hydraulic pump station. It is a device for simulating the requirements of the actual use of the car and performing the cyclic fatigue test on the constant velocity universal joint at different speeds, angles and torques. The whole of the device ..

  • 09

    2020-01

    Digital Functions of Drum Gear Couplings

    Drum tooth couplings can adapt to the adaptive and self-tuning technology of load changes, especially distributed high-end drum gear couplings with communication, networking functions and integrated PLC; on the other hand, they are simple or industry-specific Drum gear couplings and mechatronics, miniaturized drum gear couplings ..

  • 08

    2020-01

    Structural characteristics of linear spring couplings

    (1) In order to improve compensation and withstand starting shocks, variable load shocks, and vibration absorption, adjust the compensation capacity of the coupling by changing the number, length, and diameter of the linear paralysis. (2) The oil film is formed by filling solid grease in the coupling spring and in the hole where the spring pin is located ..

  • 07

    2020-01

    How to disassemble the drive shaft assembly

    1 Take out the elastic retaining ring for the hole with needle-nose pliers, and use a copper hammer to lightly and evenly tap the threaded head of the steering shaft until the bearing outer ring comes out of the inner hole of the bearing. . Note that when a copper hammer strikes the threaded head of the steering shaft, measures to protect the thread should be taken to prevent the thread from deforming. ..

  • 06

    2020-01

    How to find the alignment error of the coupling and the solution to the error

    In chemical plants, 50% to 70% of the damage to transmission equipment is caused by the misalignment of the coupling.The direct loss is the cost of replacing spare parts, and the indirect loss is the unplanned shutdown and the greater loss of shutdown profit How to find the alignment error of the coupling early and take measures in time ...

  • 04

    2020-01

    Gear ratio of reducer

    In the case of constant center distance a, when the transmission ratio i = 4.5, for typical cases: carburizing and quenching of sun gear and planet gear, hardness of tooth surface 57 ~ 61HRC; quenching and tempering treatment of internal gear, hardness 262 ~ 293HBS Has a higher carrying capacity. 2.More on structural layout ..

  • 03

    2020-01

    Coupling drives machinery industry progress and development

    The development direction of the coupling industry can be seen. Paying attention to the low-carbon problems of the coupling manufacturing industry and the entire industrial chain, in addition to raw materials, production equipment and exhaust gas treatment, the coupling manufacturing industry should be implemented to a large extent Intelligent production. At the same time, we also actively purchase advanced low-energy-consumption environmental protection processing equipment and exhaust gas ...

  • 02

    2020-01

    What are the precautions for hot-installed couplings?

    The preparation of coupling hot-packing is first washed and cleaned with gasoline or kerosene. If there are rough and damaged conditions, you should use whetstone and emery cloth to eliminate them, or treat them by other methods. Next, use a micrometer and a micrometer to carefully measure the journal and coupling inner diameter, respectively.

  • 30

    2019-12

    Basic structure of permanent magnet coupling

    The permanent magnet coupling is a coupling that uses the magnetism of a permanent magnet for transmission. This kind of coupling does not have direct contact between the main and driven half couplings, so there is no friction, no noise, and Absorbs a certain degree of axial and angular displacement errors, and can play a slippery and protective role when overloaded. It is suitable for light high-speed ..

    上一页 1 2 3 4 5 下一页 尾页 HomePrevious1 2 3 4 5NextLast

    News 丨 NEWS

    Contact 丨 CONTACT

    • Contact: Chen Kai (General Manager)
    • Consulting Hotline: 13756696728
    • Landline: 0523-84685596
    • Address: Team 10, Zengguang Village, Dongxing Town, Jingjiang City
    Home
    phone
    SMS
    contact
    Baidu search: